|
|
|
|
|
|
|
|
|
|
|
|
|
This is the #2 Desoldering Wick manufactured by Tech Spray. It is used for removing solder to replace electronic components. The Braid is also great for removing any built-up or excessive solder. Tech Spray specially designed this to be a No Clean Wick, which means it does not leave behind any ionic flux residue. That means, with this No Clean technology, you no longer have to worry about flux branches (dendrites) collecting together and causing short circuits. This product is effective on both lead and lead free solders.
|
This #3 Braid No Clean Wick is used in removing solder to replace electronic components. It is also great for removing built-up or excessive solder. With Tech Spray's NoClean Wick design you do not have to worry about this wick leaving behind ionic fluxes that can collect together and create branches (dendrites). These dendrites, if built-up enough, can cause short circuits to occur between leads or traces.
|
This is the #3 Braid No Clean Wick made by Tech Spray. This is a Desoldering Wick that removes soldering to replace electronic components. It also is great for removing built-up solder or excessive amounts of solder. This wick is specially designed to not leave behind any ionic flux residues. With no ionic flux residues, you no longer have to worry about branches (dendrites) forming and causing short circuits.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Clearance
|
Tightly wrapped, pre-cleaned cotton ensures the least amount of extractable contaminants.
|
Hydrocarbon based defluxer formulated to be powerful, yet very economical. Eliminates brushing and scrubbing, saving time and materials
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Maintenance cleaners clean oil and contaminants off of metal parts, printed circuit boards, barcode instruments, switch boxes, gear boxes, and engines. Techspray has produced Blue Shower maintenance cleaners for over 30 years, making Blue Shower a staple in maintenance departments all over the world! E-Line is a hydrocarbon-based cleaner formulated to be powerful, yet very economical. Eliminate brushing and scrubbing, saving time and materials.
|
This is a Freezer (1672-10S) made by Tech Spray. This Freezer is a swiftly evaporating liquid that super-chills isolated areas. The freezer is ideal for troubleshooting intermittently faulty capacitors, semiconductors, resistors, and other defective electronic components. It also provides you the ability to maximize the visibility of cold shoulder cracks, joints in printed circuit boards and oxidized junctions.
|
This is a Duster (1671-10S) made by Tech Spray. It has a high velocity force that is able to blow away dust, lint, microscopic contaminant, oxide deposits and other pollutants that threaten your electronics with heat build-ups and short circuits. Before you use the computer duster, press the actuator that clears the valve of any liquid. You also should only use short bursts to prevent the can from becoming freezing cold.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This is a non-flammable Duster with a high velocity force perfecting for blasting away dirt, dust, lint, metallic oxide deposit, microscopic contaminants and anything else that can damage those sensitive electronics.
|
Hydroentangled cellulose/polyester wipe with high absorbency and extra low particulate count and no chemical extractables.
|
Rapidly evaporating liquid that super-chills isolated areas. Used as a troubleshooting aid for intermittently faulting capacitors, resistors, semiconductors, and other defective components. It also increases visibility of cold solder joints, cracks in printed circuit boards and oxidized junctions. Contains additive that avoids static build-up, critical when working with ESD-sensitive components.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Flux removers (defluxers) remove flux residues and other contaminants left by manufacture, rework, or repair of printed circuit boards. Residues from higher, lead-free temperatures are more baked on and harder to clean. G3, Ecoline and Precision-V flux removers have been proven very effective at removing fluxes baked on at lead-free temperatures. Micro-components and fine pitch leads are delicate and easily damaged, so brushing and scrubbing should be avoided if possible. Both G3, Ecoline and Precision-V have a powerful spray and strong solvent that blasts off residues and cleans areas under components that a brush cannot touch. Patented defluxer formulated to be powerful and non-flammable, yet economical. The Flux Remover can safe you time and resources by eliminating brushing and scrubbing.
|
Lint-free, tear-resistant wipes saturated with 99.8% anhydrous (containing as little water as possible) isopropyl alcohol (IPA) for fast-drying cleaning. Made of hydro-entangled polyester or poly-cellulose material. Ideal for surface cleaning, stencil and tool cleaning, and PCB cleaning.
|
Non-flammable, strong cleaner ideally suited for metal cleaning. Can also be used as a defluxer when soldering components.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This Conductive Pen by Tech Spray, has easy to see silver ink that is perfect for repairing electronic traces. This pen is specially designed to make high quality conductive silver traces. Meets J-STND-001C for PCB rework and repair.
|
This is a high quality, high precision cleaner made by the people who make the best cleaners in the world, Tech Spray. This is a non-flammable cleaner and is for more sensitive rubbers and plastics that tend to swell easily. 100% AK225, which is a VOC exempt cleaner.
|
This is the #4 Desoldering Wick made by Tech Spray. This wick is used for removing solder to replace electronic components, but is also great for removing built-up or excessive solder. This desoldering braid was specially designed to not leave behind any ionic flux residues, which means you no longer have to worry about flux branches (dendrites) forming and causing short circuits. This product effectively works with both lead and lead-free solders.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This NoClean desoldering Wick (braid) by Tech Spray is used for removing solder, which helps with replacing old electronic components. This wick is also great for removing built up or excessive solder. By having yellow pre-fluxed copper this wick doesn't leave any ionic flux residues behind that can collect together and create branches (dendrites).
|
|
|
